Hello L4 hackers. I have two question (My question 1, 2 ). please help me. I'm trying to boot 'L4Linux + L4re + Fiasco' in Freescale i.MX6 Quad SABRE SD board (Cortex-A8, ARMv7-A). Such as.. 0. Get Source and install required package. |$ cd /somedir/tudos $ svn cat http://svn.tudos.org/repos/oc/tudos/trunk/repomgr | perl - init http://svn.tudos.org/repos/oc/tudos fiasco l4re l4linux_requirements| 1. L4 Re : configure and build (Success) |||==========================================================================| $ mkdir -p /path/to/obj/tudos |$ make O=/path/to/obj/tudos oldconfig $ make O=/path/to/obj/tudos -j2| |==========================================================================| 2. Fiasco : configure and build (Success) |==========================================================================| ||$ cd /somedir/tudos/src/kernel/fiasco |$ make BUILDDIR=/path/to/obj/fiasco $ cd /path/to/obj/fiasco $ make menuconfig $ make| |==========================================================================| 3. L4 linux : configure and build. (Failure) (Here, i have trouble to build l4 linux after configure according to my board ) |==========================================================================| |$ cd /somedir/tudos $ svn co http://svn.tudos.org/repos/oc/l4linux/trunk l4linux $ cd l4linux $ mkdir /path/to/obj/l4linux $ make L4ARCH=arm CROSS_COMPILE=arm-linux- O=/path/to/obj/l4linux arm_defconfig # In the menu, in "L4Linux configuration", set "L4 tree build directory" to /path/to/obj/tudos $ make L4ARCH=arm CROSS_COMPILE=arm-linux- O=/path/to/obj/l4linux menuconfig ||==========================================================================| To configure according to my board(Freescale i.MX6q_sabre_sd), I was able to choice two kinds. <The first > |System type -> ARM system type (L4 Linux) Build type (Use ARMv7) | <Result of the first > 1) Sucess build L4 linux and i got 'vmlinuz.arm' 2) 'make uImage' according to module.list |========================================================================== entry L4Linux_xs_2 kernel fiasco -nokdb roottask moe rom/l4linux.cfg module l4linux.cfg module l4re module ned module vmlinuz.arm module ramdisk-arm.rd| |==========================================================================| 3) i make SD Card bootable by u-boot.bin and bootstrap.uImage 4) Booting L4Linux + L4re + Fiasco in Freescale i.MX6q_sabre_sd But, i have problem to boot it. =========================================================================== U-Boot 2009.08 (Aug 16 2013 - 12:04:20) CPU: Freescale i.MX6 family TO1.2 at 792 MHz Thermal sensor with ratio = 180 Temperature: 44 C, calibration data 0x5764ba7d mx6q pll1: 792MHz mx6q pll2: 528MHz mx6q pll3: 480MHz mx6q pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 66000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 264000000Hz emi_slow clock: 132000000Hz ddr clock : 528000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz nfc clock : 24000000Hz Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ] Boot Device: SD I2C: ready DRAM: 1 GB MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3 In: serial Out: serial Err: serial i2c: I2C3 SDA is low, start i2c recovery... I2C3 Recovery success Found PFUZE100! deviceid=10,revid=11 Net: got MAC address from IIM: 00:04:9f:02:70:b5 FEC0 [PRIME] Hit any key to stop autoboot: 0 mmc2 is current device MMC read: dev # 2, block # 2048, count 17408 ... 17408 blocks read: OK ## Booting kernel from Legacy Image at 10800000 ... Image Name: L4 Image #7 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 7680000 Bytes = 7.3 MB Load Address: 11000000 Entry Point: 11000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... ========================================= <My question 1.> Why hang at 'Starting kernel ...' ? Setting environment variable and bootcmd , i have thought the setting is no problem. This kernel image is wrong? <The Second > |System type ---> ARM system type (Allow multiple platforms to be selected)| Multiple platform selection ---> ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait) Build type Freescale i.MX family Freescale i.MX support ---> i.MX6 Quad/DualLite support <Result of the second > i could not build l4 linux because.. GEN /path/to/obj/l4linux/Makefile scripts/kconfig/conf --silentoldconfig Kconfig ERROR: CONFIG_ARM_PATCH_PHYS_VIRT must not be enabled. make[1]: *** [check_linux_config] Error 1 make: *** [sub-make] Error 2 <My question 2.> Why can not build L4 linux according to this config ? and What is CONFIG_ARM_PATCH_PHYS_VIRT ? Please any help.. /Regards, Taeung Song | Student of Computer Engineering Hansung University. /