About build of L4Linux

[Lin]

> > I attached the log which all of serial output are written in.
> > I could not find any messages which is relate to this freeze.
> > Do you have anything about it ?
>
> The kernel command line says that the kernel output goes to the second
> serial interface. Obviously you won't see more Linux kernel messages in
> the Fiasco debug log as well as in any Dope window. Do you see something
> on ttyS1? If you want to see more messages in the debug log, enable the
> "serial driver" under "stub drivers" in L4Linux and replace the
> console=... option with console=ttyLv0
> If you leave it out or write console=tty0 the output will go to the Dope
> window.

There is no message on ttyS1.
I changed "console=ttyS1,1152000" to "console=ttyLv0" and enable
serial console support on L4Linux configration.
The result is the following (when using DOpE).

--------------------------------------------------
.....
Linux version 2.6.21-l4 () (gcc version 3.4.6 20060404 (Red Hat
3.4.6-4)) #11 Sat Jul 14 15:48:16 JST 2007
CPU: Vendor unknown, using generic init.
CPU: Your system may be unstable.
 dm_phys: 0000000000800000 - 0000000010800000 (usable)
256MB memory available.
Zone PFN ranges:
  DMA             0 ->      512
  Normal        512 ->    67584
early_node_map[1] active PFN ranges
    0:        0 ->    67584
Allocating PCI resources starting at 20000000 (gap: 10800000:ef800000)
Built 1 zonelists.  Total pages: 67056
Kernel command line: earlyprintk=yes console=ttyLv0 mem=256M
video=l4fb root=/dev/hda1
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1995.006 MHz processor.
disabling early console
Console: colour dummy device 80x25
l4ser_init_ports
l4ser: input not enabled!
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 259456k/270336k available (2346k kernel code, 2536k reserved,
710k data, 244k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffffd000 - 0xfffff000   (   8 kB)
    vmalloc : 0x18000000 - 0x20000000   ( 128 MB)
    lowmem  : 0x00000000 - 0x10800000   ( 264 MB)
      .init : 0x00700000 - 0x0073d0c0   ( 244 kB)
      .data : 0x0064a9c4 - 0x006fc34c   ( 710 kB)
      .text : 0x00400000 - 0x0064a9c4   (2346 kB)
l4lx_irq_timer_startup(0)
l4lx    | l4lx_thread_create: Created thread 0e.05 (timer.i0)
timer_irq_thread: Starting timer IRQ thread.
Calibrating delay using timer specific routine.. 3990.83 BogoMIPS (lpj=19954193)
Mount-cache hash table entries: 512
Compat vDSO mapped to 0040e000.
CPU: GenuineIntel Intel(R) Pentium(R) M processor 2.00GHz stepping 08
NET: Registered protocol family 16
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#04)
(try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
  IO window: b000-bfff
  MEM window: d0000000-d00fffff
  PREFETCH window: 24000000-240fffff
PCI: Bridge: 0000:00:1c.1
  IO window: c000-cfff
  MEM window: d0100000-d01fffff
  PREFETCH window: 24100000-241fffff
PCI: Bus 4, cardbus bridge: 0000:03:0d.0
Time: tsc clocksource has been installed.
  IO window: 0000d000-0000d0ff
  IO window: 0000d400-0000d4ff
  PREFETCH window: 20000000-23ffffff
  MEM window: 28000000-2bffffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: d0200000-d02fffff
  PREFETCH window: 20000000-23ffffff
NET: Registered protocol family 2
l4lx    | l4lx_thread_create: Created thread 0e.06 (Idler)
l4dope  | input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
l4dope  | input: AT Raw Set 2 keyboard on isa0060/serio0
l4dope  | input: PC Speaker
l4dope  | input: L4 input event injector
l4dope  | L4 input event injector: IRQ handler up
l4dope  | connect "ImPS/2 Logitech Wheel Mouse", isa0060/serio1/input0
l4dope  | connect "AT Raw Set 2 keyboard", isa0060/serio0/input0
l4dope  | connect "PC Speaker", isa0061/input0
l4dope  | connect "L4 input event injector", l4/sys
l4dope  | SharedMem(alloc): hl.raw=e0000, id=69, size=800
l4dope  | SharedMem(get_adr): address = 0x6000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=6a, size=800
l4dope  | SharedMem(get_adr): address = 0x7000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=6b, size=800
l4dope  | SharedMem(get_adr): address = 0xd000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=6c, size=800
l4dope  | SharedMem(get_adr): address = 0xe000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=6d, size=800
l4dope  | SharedMem(get_adr): address = 0xf000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=6f, size=800
l4dope  | SharedMem(get_adr): address = 0x16000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=70, size=800
l4dope  | SharedMem(get_adr): address = 0x17000
l4dope  | SharedMem(alloc): hl.raw=e0000, id=75, size=484
l4dope  | SharedMem(get_adr): address = 0x21000
l4dope  | dope: paddr=c0000000 size=7872KiB
l4dope  | Mapped video memory at c0000000 to 00800000+000000 [7872kB] via L4IO
l4dope  | mapping: vaddr=0x800000 size=8060928(0x7b0000) offset=0(0x0)
l4dope  | Frame buffer base:  0x800000
l4dope  | Resolution:         1024x768x16
l4dope  | Bytes per scanline: 2048
l4dope  | Current video mode is 1024x768 red=11:5 green=5:6 blue=0:5 res=0:0
(stop here)
--------------------------------------------------

Without DOpE, the messages of "l4dope" (last 32 lines) don't exist and
others are the same.
I'm not able to find any problems in these messages...
It seems there is no too serious message in this Log.
Could I request your opinion again ?


Regards,
Lin