Hi,

On 21.04.2014, at 03:44, Taeung treeze.taeung@gmail.com wrote:

Hi, Matthias.

Thank you for answering.

Sorry, I apologize for the late response.

I've configured the NIC driver as follows.. '[*]Network support ' and '[*]Network device driver support'.

I don't know how to init the driver,but when I run 'ifconfig', I saw nothing.

What I meant was, do you see any log output from the driver when L4Linux is booting? You can check the driver sources for ‘printk’ or ‘pr_[info,err,dbg]’ statements so that you know what you have to look for.

Matthias.

So, I guess that the cause is 'init' could not have been run. When I've done booting L4Linux, I found '/etc' folder is not enough. And I found '/proc' and '/sys' is empty. So, I've manually mounted '/proc' and '/sys'. And I'm trying to run 'ifup -a' but I've failed secure Ethernet on L4 Linux.

What I mistake ?

(Mentioned above is same as mail before last)

And I'm doubting 'arm-rv.io' and 'l4lx_xs.cfg' I'm using. Must I modify them ?

If you give me small hints, I'd apperciate. Thank you !!

For reference.

I'm using 'entry L4Linux_XS' as follows

entry L4Linux_XS roottask moe rom/l4lx_xs.cfg module l4re module ned module l4lx_xs.cfg module io module arm-rv.io module vmlinuz.arm module ramdisk-arm.rd ======================== arm-rv.io in example folder is.. ======================== hw-root { NIC => new Device() { .hid = "smsc911x"; new-res Mmio(0x4e000000 .. 0x4e000fff); new-res Irq(60); } }

l4lx => new System_bus() { NIC => wrap(hw-root.NIC); } ======================== l4lx_xs.cfg is .. ======================== -- vim:set ft=lua:

local lxname = "vmlinuz"; if L4.Info.arch() == "arm" then lxname = "vmlinuz.arm"; end

L4.default_loader:start( { caps = { log = L4.Env.log:m("rws"), }, l4re_dbg = L4.Dbg.Warn, log = { "l4linux", "yellow" }, }, "rom/" .. lxname .. " mem=64M console=ttyLv0 l4x_rd=rom/ramdisk-" .. L4.Info.arch() .. ".rd root=1:0 ramdisk_size=4000 init=/bin/sh"); ========================

• Taeung -

On 04/18/2014 09:21 PM, Matthias Lange wrote:

...

Hi,

On 18.04.2014, at 13:24, Taeung treeze.taeung@gmail.com wrote:

...

Hello, Adam and L4 Hackers. Thanks for answering.

When I run 'ifconfig', nothing have happened. I guess that the cause is /etc folder in ramdisk is not enough to run 'init'.

Would you mind if I ask you another question ?

Must also I modify 'arm-rv.io' ? or must I modify 'l4lx_xs.cfg' ? or Do not I need do it ?

If I have to modify them , how to modify ? (I'm using Freescale imx6q SABRE SD board.)

If you give a bit me hints, I'd appreciate.

Do you have configured the NIC driver into L4Linux? Do you see L4Linux trying to init the driver. I fear your questions are to generic to give a specific answer.

Matthias.

-- matthias.lange@kernkonzept.com - Tel. 0351-41 888 614

Kernkonzept GmbH. Sitz: Dresden. Amtsgericht Dresden, HRB 31129. Geschäftsführer: Dr.-Ing. Michael Hohmuth